Log in
EN
Start trial
How it worksRemote accessBenefitsMonitorAI integrationTimelineChartsProjectSupported loggersNewsPricingFAQLog in

Supported loggers › Wiser for KNX

Wiser for KNX

Wiser for KNX has a built-in KNX bus connection, so it works as the KNXSENSE logger without a separate KNX/IP gateway.

Wiser for KNX as the KNXSENSE logger
How it works

How the logger works.

The KNXSENSE logger is installed on the device as separate software. It has no effect on anything else the device does. Logic, visualisation, interfaces and scripts keep running as normal.

The logger only reads bus traffic and never writes to the bus. The connection is established outbound from the site, so no open ports and no static IP address are needed. The logger also works behind a shared carrier IP address.

Logging requires Wiser for KNX to be powered on continuously and the site to have an internet connection.

Specifications
Manufacturer
Schneider Electric
Remote ETS access
Via KNXSENSE
Manufacturer’s product page
se.com →

KNXSENSE-compatible models

  • LSS100100
1.0  main lineroutednot routed1.1.01.2.01.3.0loggerLine 1.1Line 1.2Line 1.3KNXSENSE400-day recording400 days agotoday
Logging coverage

How telegrams reach the recording.

Wiser for KNX is connected directly to the KNX bus, so it sees the telegram traffic on its own line and everything the line couplers route onto that line from the other lines.

KNXSENSE compares the addresses it sees against your ETS project and tells you straight away which lines and devices are in the recording and which are missing.

KNX telegram logging

KNX bus monitoring in your browser.

Jokainen sanoma, jonka Wiser for KNX näkee väylällä, tallentuu ympäri vuorokauden millisekunnin tarkkuudella tietoturvallisille palvelimillemme , myös silloin, kun et ole paikalla.

Telegram-level history reaches 400 days back on a rolling window. You can browse it in your browser, on any device, without the ETS software.

TimeSource addressSource nameDestination addressDestination nameValue
09:14:02.1811.1.34Zennio QUAD Plus0/6/1Scene: leaving home1
09:14:02.8701.1.11ABB SA/S 8.16.5.2 Switch Actuator0/1/14Kitchen: worktop lighting CONTROLon
09:14:03.9801.2.3Theben RMG 8 S KNX0/3/9Facade lighting CONTROLoff
09:14:05.0902.1.23ABB SA/S 8.16.5.2 Switch Actuator0/4/3Guest house: terrace lighting CONTROLoff
09:14:05.2091.1.35MDT Shutter Actuator JAL-0810.023/1/12Bedroom: venetian blind POSITION100%
09:14:05.3281.1.25Elsner Intra-Sewi KNX TH-L1/1/54Measured room temperature: Bathroom24.6°C
09:14:05.3911.1.20Gira Tastsensor 4 Komfort0/1/9Bedroom: night light CONTROLoff
09:14:05.4653.1.23ABB ZS/S 1.1 Meter Interface3/2/11Solar PV output2,415W
09:14:06.5751.2.3Theben RMG 8 S KNX0/3/4Outdoor lighting: driveway CONTROLon
09:14:06.6491.1.39Berker B.IQ push button3/2/7Blinds: west facade MOVEdown
09:14:06.7231.1.25Elsner Intra-Sewi KNX TH-L1/4/3Relative humidity: Bathroom58%
09:14:06.7971.1.37MDT Dimming Actuator AKD-0424V.020/2/21Dining area: pendant light VALUE25%
Remote KNX access

ETS tunnelling through KNXSENSE.

You open the connection from the interface, and from there you program the site in ETS as if you were on site.

Logging reserves no ETS tunnel slots at all. All tunnel slots stay available for ETS.

Remote access is included in the KNXSENSE monthly fee. No separate portal, licence or port forwarding is needed.

Setup

Setting up Wiser for KNX as a KNX logger.

KNXSENSE’s setup assistant walks you through the right settings step by step.

The whole setup takes only a few minutes.

  1. Import your ETS projectNames and structure from the project into KNXSENSE
  2. Install the loggerGuided install on the device
  3. Logging is runningThe first telegram from the site’s bus confirms the connection

Setup is a one-off job. When updates to the logger are released, they are installed on the device automatically. Updating requires no action from you and no visit to the site.