Log in
EN
Start trial
How it worksRemote accessBenefitsMonitorAI integrationTimelineChartsProjectSupported loggersNewsPricingFAQLog in

Supported loggers › Gira S1

Gira S1

The Gira S1 works as a KNXSENSE logger through its own bus connection, with no separate KNX/IP gateway.

Gira S1 as the KNXSENSE logger
How it works

How the logger works.

KNXSENSE reads the bus through the Gira S1's secure remote access, and nothing is installed on the device. Logging has no effect on anything else the device does. Remote access, tunnelling and its other duties carry on as normal.

The logger only reads bus traffic and never writes to the bus. The connection is established outbound from the site, so no open ports and no static IP address are needed. The logger also works behind a shared carrier IP address.

Logging requires the Gira S1 to be powered on continuously and the site to have an internet connection.

Specifications
Manufacturer
Gira
Remote ETS access
Via KNXSENSE
Manufacturer’s product page
katalog.gira.de →

KNXSENSE-compatible models

  • 2089 00
1.0  main lineroutednot routed1.1.01.2.01.3.0loggerLine 1.1Line 1.2Line 1.3KNXSENSE400-day recording400 days agotoday
Logging coverage

How telegrams reach the recording.

The Gira S1 is connected directly to the KNX bus, so it sees the telegram traffic on its own line and everything the line couplers route onto that line from the other lines.

Telegrams are read in real time and there is no local storage on site: an outage leaves a gap that is documented in the recording.

KNXSENSE compares the addresses it sees against your ETS project and tells you straight away which lines and devices are in the recording and which are missing.

KNX telegram logging

KNX bus monitoring in your browser.

Jokainen sanoma, jonka Gira S1 näkee väylällä, tallentuu ympäri vuorokauden aikaleimoineen tietoturvallisille palvelimillemme : myös silloin, kun et ole paikalla.

Telegram-level history reaches 400 days back on a rolling window. You can browse it in your browser, on any device, without the ETS software.

TimeSource addressSource nameDestination addressDestination nameValue
09:14:02.1811.1.46MDT SCN-RT1GS.011/1/26Measured room temperature: Living room21.8°C
09:14:02.8703.1.48ABB EM/S 3.16.1 Energy Actuator2/4/14(DB1) EV charging power3,680W
09:14:03.2811.1.13Zennio QUAD Plus1/1/18Measured floor temperature: Master bedroom23.4°C
09:14:04.3911.1.21Berker B.IQ push button3/2/7Blinds: west facade MOVEdown
09:14:04.4651.1.2MDT Switch Actuator AKK-1216.030/1/6Hallway: ceiling lighting CONTROLon
09:14:04.5391.1.9Elsner Intra-Sewi KNX TH-L1/4/3Relative humidity: Bathroom58%
09:14:04.6131.2.3Elsner Suntracer KNX sl0/5/6Wind speed4.2m/s
09:14:04.7322.1.7ABB SA/S 8.16.5.2 Switch Actuator0/4/3Guest house: terrace lighting CONTROLoff
09:14:05.0081.1.34ABB DALI-Gateway DG/S 8.10/2/12Corridor lighting: dimming VALUE40%
09:14:05.0711.1.47MDT Dimming Actuator AKD-0424V.020/2/21Dining area: pendant light VALUE25%
09:14:06.1811.1.34ABB DALI-Gateway DG/S 8.10/2/5Living room: general lighting VALUE72%
09:14:06.2551.2.12Theben RMG 8 S KNX0/3/9Facade lighting CONTROLoff
Remote KNX access

ETS tunnelling through KNXSENSE.

You open the connection from the interface, and from there you program the site in ETS as if you were on site.

Logging takes no ETS tunnel slots. The logger reads the bus with multicast routing, which takes no tunnel slots at all, so all of the device’s slots stay available for ETS. Remote ETS access through KNXSENSE takes one slot, but only for the duration of the remote session.

Remote access is included in the KNXSENSE monthly fee. No separate portal, licence or port forwarding is needed.

Setup

Setting up the Gira S1 as a KNX logger.

You enable the Gira S1's own remote access and connect the site to KNXSENSE. Logging starts as soon as the connection to the site’s bus is up.

The guided setup walks through the prerequisites and tells you at once if any of them is missing. Logging reserves the device’s VPN connection.

  1. Allow remote accessEnable the device’s own remote access as the manufacturer instructs
  2. Import your ETS projectNames and structure from the project into KNXSENSE
  3. Logging is runningThe first telegram from the site’s bus confirms the connection

Setup is a one-off job. The logger is not software on the device, so KNXSENSE updates require no action from you and no visit to the site. Updating the device’s own firmware stays your job, as before.