Log in
EN
Start trial
How it worksRemote accessBenefitsMonitorAI integrationTimelineChartsProjectSupported loggersNewsPricingFAQLog in

Supported loggers › Elsner KNX Matter Server

KNX Matter Server

The Elsner KNX Matter Server has a built-in KNX bus connection, so it works as the KNXSENSE logger without a separate KNX/IP gateway.

Elsner KNX Matter Server as the KNXSENSE logger
How it works

How the logger works.

The KNXSENSE logger is installed on the device as separate software. It has no effect on anything else the device does. Logic, visualisation, interfaces and scripts keep running as normal.

The logger only reads bus traffic and never writes to the bus. The connection is established outbound from the site, so no open ports and no static IP address are needed. The logger also works behind a shared carrier IP address.

Logging requires the KNX Matter Server to be powered on continuously and the site to have an internet connection.

Specifications
Manufacturer
Elsner Elektronik
Remote ETS access
Via the device’s own channel
Manufacturer’s product page
elsner-elektronik.de →

KNXSENSE-compatible models

  • 71256
1.0  main lineroutednot routed1.1.01.2.01.3.0loggerLine 1.1Line 1.2Line 1.3KNXSENSE400-day recording400 days agotoday
Logging coverage

How telegrams reach the recording.

The KNX Matter Server is connected directly to the KNX bus, so it sees the telegram traffic on its own line and everything the line couplers route onto that line.

KNXSENSE compares the addresses it sees against your ETS project and tells you straight away which lines and devices are in the recording and which are missing.

KNX telegram logging

KNX bus monitoring in your browser.

Jokainen sanoma, jonka KNX Matter Server näkee väylällä, tallentuu ympäri vuorokauden millisekunnin tarkkuudella tietoturvallisille palvelimillemme , myös silloin, kun et ole paikalla.

Telegram-level history reaches 400 days back on a rolling window. You can browse it in your browser, on any device, without the ETS software.

TimeSource addressSource nameDestination addressDestination nameValue
09:14:02.1811.2.14Hager TXA610B0/4/8Carport: lighting CONTROLon
09:14:02.2553.1.18ABB EM/S 3.16.1 Energy Actuator2/4/14(DB1) EV charging power3,680W
09:14:02.5311.1.6Theben HMT 6 S KNX1/2/11Bathroom: underfloor heating CONTROLon
09:14:02.8071.1.14ABB JRA/S 8.230.5.1 Blind Actuator3/1/5Living room: awning MOVEup
09:14:03.9171.1.36Berker B.IQ push button3/2/7Blinds: west facade MOVEdown
09:14:04.3281.1.2MDT SCN-RT1GS.011/1/26Measured room temperature: Living room21.8°C
09:14:04.3911.1.34MDT Heating Actuator AKH-0800.031/2/26Living room: valve position34%
09:14:04.5101.1.30MDT Shutter Actuator JAL-0810.023/1/12Bedroom: venetian blind POSITION100%
09:14:04.5841.1.38Steinel IR Quattro HD KNX0/7/0Presence detector, lobby: lux level138lux
09:14:04.7031.2.32MDT Switch Actuator AKK-1216.030/3/7Outdoor lighting: garden CONTROLon
09:14:05.3921.1.10MDT Glass Push Button II3/2/4Blinds: south facade POSITION65%
09:14:05.4552.1.34ABB SA/S 8.16.5.2 Switch Actuator0/4/3Guest house: terrace lighting CONTROLoff
Remote KNX access

ETS tunnelling over the device’s own route.

The device has its own remote access, included at no extra cost. ETS sees it as an ordinary KNX/IP gateway, so you program the site as if you were there, with no ports opened on site. The connection is opened from the device’s own interface.

Logging reserves no ETS tunnel slots at all. The device’s own KNX/IP gateway offers four tunnel slots for ETS.

KNXSENSE does not provide its own ETS tunnelling for this device. Remote access runs over the device’s own route alongside logging.

Setup

Setting up the KNX Matter Server as a KNX logger.

KNXSENSE’s setup assistant walks you through the right settings step by step.

The whole setup takes only a few minutes.

  1. Import your ETS projectNames and structure from the project into KNXSENSE
  2. Install the loggerGuided install on the device
  3. Logging is runningThe first telegram from the site’s bus confirms the connection

Updates are made in the device’s user interface. When an update is released for the logger, you apply it from the setup wizard. It is the same few-minute task as the installation.